//Process Setup
char PS_MI01[] = "Tares";
char PS_MI02[] = "Calibration";
char PS_MI03[] = "Quantités";
char PS_MI04[] = "Automatique";
char PS_MI05[] = "Servomoteur";
char PS_MI06[] = "Paramètres";
char PS_MI07[] = "Compteur";
char PS_MI08[] = "Compt.Cession";
char PS_MI09[] = "Param.Usine";
char PS_MI10[] = "INA219 Setup";

//Setup Tarawerte
char ST_TI01[] = "Tares des pots";
char ST_TI02[] = "manquantes";

//Setup Kalibration
char SC_TO01[] = "Calibration";
char SC_LI01[] = "Vider la balance";
char SC_LI02[] = "et confirmez";
char SC_LI03[] = "avec OK";
char SC_LI04[] = "Posez";
char SC_LI05[] = "et confirmez";
char SC_LI06[] = "avec OK";

//Setup Fuellmenge
char SF_TO01[] = "Quantités des pots";

//Setup Automatik
char SA_TO01[] = "Automatique";
char SA_MI01[] = "Démarrage Auto";
char SA_MI02[] = "Tolérance pots";
char SA_MI03[] = "Correction";
char SA_MI04[] = "Autocorrection";
char SA_MI05[] = "-> Surremplissage";
char SA_MI06[] = "Flux g/temps";
char SA_MI07[] = "Sauvegarder";

//Setup Servo
char SS_TO01[] = "Servomoteur";
char SS_MI01[] = "Livesetup";
char SS_MI02[] = "Minimum";
char SS_MI03[] = "Dosage fin";
char SS_MI04[] = "Maximum";
char SS_MI05[] = "Sauvegarder";

//Setup Parameter
char SP_TO01[] = "Paramètres";
char SP_MI01[] = "Buzzer";
char SP_MI02[] = "LED";
char SP_MI03[] = "Montrer logo";
char SP_MI04[] = "Montrer crédits";
char SP_MI05[] = "Schéma de couleur";
char SP_MI06[] = "Couleur du marqueur";
char SP_MI07[] = "Sauvegarder";

//Setup Zählwerk/ZählwerkTrip
char SZ_TO01[] = "Compteur";
char SZ_TO02[] = "Compteur cession";

//Setup INA219
char SI_TO01[] = "INA219 Setup";
char SI_MI01[] = "Courant servo";
char SI_MI02[] = "Cal. robinet";
char SI_MI03[] = "Montrer courant";
char SI_MI04[] = "Sauvegarder";
char SI_LI01[] = "courant max. :";
char SI_LI02[] = "angle min. :";
char SI_LI03[] = "Calibration en cours";
char SI_LI04[] = "Courant:";
char SI_LI05[] = "Angle:";
char SI_LI06[] = "Robinet:";
char SI_LI07[] = "Calibration terminée";

//Setup Clear Preferenzes
char CP_TO01[] = "Effacer Préférences";
char CP_MI01[] = "Effacer Préférences";
char CP_MI02[] = "Effacer mémoire NVS";
//Error Messages
char ER_LI01[] = "balance";
char ER_LI02[] = "absente!";
char ER_LI11[] = "non";
char ER_LI12[] = "calibré";
char ER_LI21[] = "vider";
char ER_LI22[] = "la balance!";

//Manueller Modus
char MM_TO01[] = "Manuel";
char MM_LI01[] = "Servo:";
char MM_LI02[] = "Tare:";
char MM_LI03[] = "INA:";
char MM_LI04[] = "Coura.:";
char MM_LI05[] = "max:";
char MM_LI06[] = "réel:";
char MM_LI07[] = "A";                   //Winkel
char MM_LI08[] = "Courant servo:";
char MM_LI09[] = "Tare";

//Automatik Modus
//char AM_TO01[] = "Automatique";
char AM_LI01[] = "INA219";
char AM_LI02[] = "Démarrage auto";
char AM_LI03[] = "Autocorrection";
char AM_LI04[] = "Courant:";
char AM_LI05[] = "Correction:";
char AM_LI06[] = "Autocorr:";
char AM_LI07[] = "Min:";
char AM_LI08[] = "Max:";
char AM_LI09[] = "Reé:";
char AM_LI10[] = "Poser";
char AM_LI11[] = "le pot";
char AM_LI12[] = "START";
char AM_LI13[] = "Tare pot";
char AM_LI14[] = "Flux g/temps";
char AM_LI15[] = "Flux:";
char AM_LI16[] = "A";
char AM_LI17[] = "DA";
char AM_LI18[] = "Courant servo:";
char AM_LI19[] = "a";
char AM_LI20[] = "c";
char AM_LI21[] = "f";

char AM_ER01[] = "tare?   ";

//Diverses
char AUS[] = "non";
char EIN[] = "oui";
char DUNKEL[] = "sombre";
char HELL[] = "clair";
char SUMME[] = "Total";
char RUECKSETZEN[] = "Reset";
char ABBRECHEN[] = "Annuler";
char START[] = "Start";
char ZU[] = "ouvrir";
char OFFEN[] = "fermer";
char ZURUECK[] = "Retour";